Design Features Printing Knowledge
Design Features

Copy Design | Image Limitations | Backprinting | Marginal Words


Copy Design

Copy for integrated and affixed products can consist of rules, text, graphics, screens and halftones. When designing the copy for the carrier and product, you must keep in mind that there are image limitations on the press equipment that manufactures the carriers and affixed products. (see Image Limitations below).

Screened Copy:

  • Use it to highlight areas.
  • Use it to shade backgrounds.
  • A variety of are densities available.
  • Screened copy is supplied in a negative or on a disk.
  • Use 5% to 15% screen in areas that will be imprinted.
  • Use halftones for pictures.


 

 
Image Limitations

Web Press Equipment:

Integrated and affixed products that have a continuous or unit set carrier are most generally printed on a web press. Laser or single sheet carriers can be printed on a web press or a sheet fed press. Web presses have plate and blanket cylinders, which along with other components, produce a printed impression on paper. The plate and blanket cylinders have a slot or gap in them where the plate and the blanket are attached. Nothing can print in the gap area. The nonprintable area is known as the "cylinder gap" or the "plate lockup". The gap area is usually 3/8" in depth and extends the full width of the sheet.

 

Note: All colors have this 3/8" gap because each color is printed on a separate cylinder.

 
Three Ways To Allow for the 3/8" Gap on a Continuous Carrier

Example: A 9 1/2" x  11" form would have a maximum image of 9 1/2" x  10 5/8". 

 
Three Ways To Allow for the 3/8" Gap on a Unit Set Carrier

Example: An 8 1/2" x  11 5/8" form would have a maximum image of 8 1/8" x  11 5/8".

 
Three Ways To Allow for the 3/8" Gap on a Single Sheet Carrier
(Printed on Web Press Equipment)

Example: A 8 1/2" x  11" form would have a maximum image of 8 1/8" x  11".
 

Three Ways To Allow for the 3/8" Gap on a Laser Sheet Carrier
(Printed on Web Press Equipment)

Example: A 8 1/2" x  11" form would have a maximum image of 8 1/2" x  10 5/8".
 

Listed below are some ways that a manufacturer can work around the image limitations:

  • The manufacturer can work around image size limitations by trying to adjust the copy within the image limitations.
  • The copy can be printed as a split image (run on two separate printing units on the same press).
  • The application can be printed oversize and then trimmed to the finished size on unit set, laser and single sheet carriers.
  • Laser or single sheet carriers can be printed on sheet fed equipment.
     

Note: When discussing the image limitation options with your manufacturer, you will have to let them know how many colors you will have on the front and back of your carrier for them to determine which option they could use.

 

Sheet Fed Equipment:

Laser or single sheet carriers can be printed on sheet fed presses. The image limitations are less restrictive on sheet fed presses. The carrier can be printed oversize and trimmed to the finished size. Indicate where the copy bleeds so the supplier can allow for the proper gripper and trim needed. Although printing the form on sheet fed equipment may solve image limitations problems, it may not be cost effective if you are running a large quantity of forms.

 

Affixed Product - Image Limitations:

See the image limitations for the product type being attached. See Cards-Image Limitations or Labels-Image Limitations.

 

Integrated Product - Image Limitations:

The integrated product is actually part of the carrier so image limitations are considered along with image limitations on the carrier.


Backprinting

Backprinting is any copy printed on the back side of the carrier or affixed product.

  • The same design features are available as on the front of the carrier or affixed product.
  • The same image limitations apply to the back as on the front of the carrier or affixed product.


Marginal Words

Marginal words are printed on a dry offset unit using a rubber stamp type of material. They are generally used on the continuous or unit set carriers but can be used on laser or single sheet if required.

  • They are usually printed in a standard red ink.
  • They are used to make reference to the distribution of the form or to provide special instructions for the user.
  • They may be used as a method to add an additional color to a form, but the quality will not be as good as the quality produced by a regular offset printing unit.
  • There may be size limitations depending on your supplier's capabilities.

 


Back to Top

More Integrated and Affixed >>

Additional search results for:
   Design Features
knowledge
Design Features
Design Features
Design Features
Design Features
Design Features
Design Features
Design Features
Security Design Features
Postal Design
Copy and Design
glossary
Graphic Design
Computer Aided Design (CAD)
Search
Enter keywords to search
PrintingTips.Com Knowledge
Print Preparation
Print Products
Continuous Products
Direct Mail
Planning and Design
Component Development
Envelopes
Integrated Products
Size
Design Features
Paper
Types
Ink
Perforations
Punching
Die Cutting
Numbering
Packaging
Storage
Mailers
Single Sheet Products
Copy and Artwork Development
Production
Direct Mail Services
Planning Guide
Envelopes
Integrated and Affixed
Labels
Laser Sheets
Mailers
Single Sheet Products
Unit Sets
RelatedContent
knowledge
glossary
Features of Interest
Featured Ad
Terms of Use |  Privacy Policy |  Site Map |  Index |  Contact Us
Reproduction in whole or in part without written permission is strictly prohibited.
© Copyright 2024 Tecstra Systems, All Rights Reserved, PrintingTips.Com

Design Features - PrintingTips.com

Printing Tips Home Customer Service Knowledge Glossary Printing Tips Home