Paper Printing Knowledge
Paper

Carbonless Paper | Uncoated Paper | Carbon Interleaved Forms


A unit set is made up of two or more parts. The paper can be the same on all parts or each part can be different. The number of parts and type of paper will depend on the use of the form in the workflow process. The imaging quality from part to part of the form will be affected by the number of parts and the type of paper used for each part. Part to part imaging can be accomplished in two ways:

  • Carbonless stock, which has a coating of special chemicals, can be used. The image is transferred through the parts as the pressure of writing or typing instruments causes the chemical coatings to react with one another, resulting in an image (see below).
  • An uncoated stock, which is not coated with any image producing chemicals, can also be used. An image is produced between the parts by inserting carbon paper to make a carbon interleaved form.

Note: Imaging from part to part should not be a problem on 4 parts or less of a unit set made up of standard weight papers. Forms that are over 4 part should be tested for imaging quality.

 

Carbonless Paper

CB - Coated Back

The CB stock will transfer an image to the CFB stock or to the CF stock.
 

CFB - Coated Front & Back

The CFB stock will transfer an image to another CFB stock or to a CF stock.
 

CF - Coated Front

The CF stock does not transfer an image. It accepts the image from the CB or CFB stock.
 

The imaging happens when the CB and the CF chemical coatings react with each other, however, if you need to prevent imaging in specific areas of a carbonless form, a desensitizing ink is required.

 

Standard Carbonless Paper

Type 

Standard Weight

Parts Used On

Standard Colors

CB

15 lb.

First Part

White

CFB

14 lb.

Internal Parts

White, Canary, Pink, Gold, Green, & Blue

CF

15 lb.

Last Part

White, Canary, Pink, Gold, Green, & Blue

 

Carbonless Options

The paper options below usually add to the cost of the form.

Type

Weight

Description

CB

20 lb. & 26 lb.

20 lb and 26 lb. papers are used when part 1 needs to be of a little heavier weight for durability or when there is gong to be backprinting on part 1. The heavier weight will help prevent the backer from showing through to the front. The 26 lb. is also used for check applications. 20 lb. and 26 lb. are available in white.
 

CFB

17 lb.

17 lb. is used when the internal parts need to be a little heavier than standard weights. White, canary, and pink are readily available. Consult your manufacturer for the availability of other colors.
 

CF

27 lb., 33 lb., 105 lb.

The 27 lb., 33 lb. and 105 lb. weights are used when the last part needs to be extra durable because of handling or because of the type of application in which it will be used. It may also be used to add overall stability to the form. The 27 lb. and 33 lb. are available in white and buff; 105 lb. is available in white and manila.

 

Note: There are other specialty carbonless stocks available to you. Consult with your supplier for information on the specialty papers and their availability. 

 

Uncoated Paper

Standard Bond Paper

Type 

Standard Weight

Parts Used On

Standard Colors

Bond

15 lb.

First Part

White

Bond

12 lb.

Internal Parts

White, Canary, Pink, Gold, Green, & Blue

Bond

12 or 15 lb.

Last Part

White, Canary, Pink, Gold, Green, & Blue

 

Additional Options

The paper options below usually add to the cost of the form.

Type

Weight

Description

Bond and MICR

20 lb. & 24 lb.

20 lb. and 24 lb. are used when part 1 needs to be of a little heavier weight for durability or when heavy backprinting would show through to the front of the form. The 24 lb. is also used for check applications. The 20 lb. and 24 lb. are available in white, canary, pink, gold, green, & blue. For other available colors, consult your supplier.
 

Ledger

28 lb., 32 lb., & 36 lb.

Ledger is used when the last part needs to be extra durable because of handling or because of the application in which it will be used. It may also be used to add overall stability to the form. Ledger is available in white and buff.
 

Tag

100 lb. & 125 lb.

Tag is used when the last part needs to be extra durable because of handling or because of the application in which it will be used. It may also be used to add overall stability to the form. Tag is available in white and manila. Some manufacturers may have restrictions on running anything heavier than 100 lb. tag. If you have an application which requires a heavier stock, you should consult your manufacturer.

 

Note: Ledgers and tags should not be used for part 1 or internal parts if imaging from part to part is necessary. The heavier weight of these stocks will greatly reduce the quality of the image transfer. If you feel it is necessary to use ledger or tag stock for any part other than the last, you should request an imaging test from your supplier.

 

Note: There are many options for paper that could be used in a unit set. The preceding information described the most common papers used on standard unit sets. If you have a special request it is best to discuss it with your supplier for availability.

 

Carbon Interleaved Forms

When your form needs to have an image transferred from part to part but you are not using carbonless stock, then your form will need to have carbon paper between the parts. The following are points to consider when deciding whether or not to use carbon interleaved forms:

  • Carbon color:

Blue - Blue carbon is generally used for handwritten forms.
Black - Black carbon is generally used on forms that will be typed on or imprinted by some other type of mechanical means.

  • Carbon interleaved forms will give you a better image transfer on some forms.
  • To prevent image transfer in specific areas of the form, you can use a stripe or pattern carbon. Stripe and pattern carbons have the carbon coating applied to the carbon tissue in selected areas. The uncoated areas of tissue will prevent image transfer to the part below.

  • Feather edge carbon is used when a carbon needs to be extracted from the form before all parts are separated. It generally has a perforation at the top to assist in extraction of the carbon. Feather edge carbon would be used on a form that requires image transfer to all parts when information is first entered on the form but that cannot have additional information, that is added at a later time, transfer to one of the parts. After the initial information is entered, the feather edge carbon is extracted from between the parts where image transfer is to be prevented.

  • Carbon interleaved forms are generally less expensive than carbonless forms but they are not as clean or efficient for the end user to work with. Once the form is torn apart, you must dispose of the carbon, whereas with carbonless forms, you do not have the carbon paper.

 


Back to Top

More Unit Sets >>

Additional search results for:
   Paper
knowledge
Types of Paper
Paper
Paper
Paper
Paper
Paper
Paper
Paper
Security Paper
glossary
Writing Paper
Wove Paper
Web Paper
Virgin Paper
Vellum Paper
Uncoated Paper
Uncalendered Paper
Translucent Paper
Thermal Paper
Text Paper
Tag Paper
Search
Enter keywords to search
PrintingTips.Com Knowledge
Print Preparation
Print Products
Continuous Products
Direct Mail
Envelopes
Integrated and Affixed
Labels
Laser Sheets
Mailers
Single Sheet Products
Unit Sets
Size
Design Features
Paper
Ink
Fastening
Perforations
Punching
Numbering
Labels
PS Tape
Packaging
Storage
RelatedContent
knowledge
glossary
Features of Interest
Featured Ad
Terms of Use |  Privacy Policy |  Site Map |  Index |  Contact Us
Reproduction in whole or in part without written permission is strictly prohibited.
© Copyright 2024 Tecstra Systems, All Rights Reserved, PrintingTips.Com

Paper - PrintingTips.com

Printing Tips Home Customer Service Knowledge Glossary Printing Tips Home